Side by Side Outlet Parts and Accessories
When it comes to hardcore off-road racing, theres nothing like the thrill of bombing into a corner and accelerating past the apex. One thing many owners don't realize is the flex of their radius rods while in a corner. These forces put strain on the radius rods and translate to suspension while also misaligning the wheels. With a varying wheel alignment, the machine will handle much different due to the radius rods flexing.
The Agency Power billet radius rod alleviates this issue by reinforcing the radius rod mounting. Thanks to the CNC machined T6-6061 aluminum construction and stainless steel hardware, the radius plate provides utility, styling, and ruggedness to your machine. The build in D-Ring makes recovery a breeze whether you are pulling your friend out of the swamp or need to be pulled out of a sticky situation.
For ultimate durability and styling, the base of the radius plate is anodized black with customizable inlays. The inlays come in an anodized black, silver, red, and blue finish so you can match your machines color scheme. Installation is as easy as removing the factory radius plate and replacing it with the Agency Power billet radius rod plate
Features:
- Eliminates radius rods flexing under hard cornering
- Constructed of Billet T6-6061 aluminum
- Built in D-ring to make recovery a breeze
- CNC machined for ultimate precision
- Stainless steel hardware to prevent corrosion
- Customizable anodized inlays
- Base features an anodized black finish for durability
- Easy installation process
- Made in the USA!
- Limited One-Year Warranty
Fitment:
- Can-Am Maverick X3 2017+
Notes:
- Agency Power Offers a One-Year Warranty Against Defects or Failures
- Product Warranties Are Available For Those Who Fill Out The Online Warranty Form HERE
- Warranty is Available With Original Invoice Showing Purchase Date
The new Agency Power billet aluminum wastegate is the perfect upgrade for your Can-Am X3 turbocharger. The new wastegate features a 1bar spring housed in an 85mm body. This design allows you to easily change springs and service the wastegate if needed. As a direct bolt-on to your factory turbo, the wastegate features an adjustable rod for those that would like to set your crack pressure specifically to your build. Perfect for those looking to get better boost response out of the stock tune, an ECU flashed car, or even a turbo upgrade.
Doing a back to back dyno test, we show how the wastegate improves boost response and performance over the stock wastegate. Set at 1 full turn in from neutral, the new Agency Power billet wastegate holds 1 psi more than stock gaining you 4hp.
Features:
- Billet Aluminum Design
- Direct Bolt On
- Adjustable Rod
- Stiffer Spring
Notes:
Fitment:
- 2017-2019 Can-Am X3 Turbo, X3 X DS Turbo R, X3 X RS Turbo R 2 | 4 Door
Features:
- Provides much needed rigidity to thefront suspension
- Constructed of Billet T6-6061aluminum
- CNC machined for ultimate precision
- Customizable anodized inlays
- Base is anodized black finish fordurability
- Made in the USA!
- Limited One-Year Warranty
Fitment:
- Stylish Design with Laser Etched Agency Power Logo
- Increase Grip and Tactile Feel
- Precision CNC Machined 6061-T6 Billet
- Aluminum
- Easy Direct-Fit Installation
- Anodized Blue, Red or Black
The Agency Power passenger grab handle for the Can-Am Maverick X3 was designed with functionality and style in mind. The Maverick X3 has shown extreme versatility with vehicles being used to race, jump through the dunes, or even cruise the trails. No matter the use, it's important to have a superior grip on the grab handle when you need it. While designing the grab handle, we added finger grips to establish a more secure feel, whether you're riding with or without gloves. Each piece is precision CNC machined from a solid block of billet 6061-T6 aluminum to ensure strength without compromise. The grab handle is then finished with a durable anodized finish and laser engraved witht the Agency Power logo.
Features:
- Stylish Design with Laser Etched Agency Power Logo
- Increase Grip and Tactile Feel
- Precision Bent From 6061-T6 Billet Aluminum
- Easy Direct-Fit Installation
- Anodized Blue, Red or Black
- Includes a M6x30mm Mounting Screw and Grommet
Fitment:
- Can-Am Maverick X3 2017+
Notes:
When it comes to making more power, heat becomes an issue that can hold you back. Turning up boost pressure or upgrading to a bigger turbo will result in additional heat. This is due to the turbocharger generating more energy which is a direct translation to higher heat levels. To combat this issue, Agency Power has released a turbo/manifold blanket for your Agency Power upgraded turbo on your Polaris RZR XP Turbo!
Containing the heat produced by your turbocharger can pose many benefits. Your turbocharger will increase efficiency by isolating the heat to the hot side. This will keep heat away from the compressor side which results in cooler intake air temperatures (IAT). Reducing the IAT will correspond to extra horsepower. Additionally, having the heat dispersed through the turbo blanket will reduce the overall engine bay temperature up to 60-percent.
The blanket consists of pulverized volcanic lava rock woven into a tight weave that can withstand a whopping 1800°F of direct heat and 2500°F of radiant heat. The inner insulation layer is constructed from extreme conditions calcium magnesium silicate wool. To tie everything together, a fine weave steel mesh conjoins all the materials to provide ultimate heat containment.
Features:
- Fit's Agency Power big turbo upgrade
- Reduces the overall engine bay temperature by 60-percent
- Can withstand 1800°F of direct heat and 2500°F of radiant heat
- The outer layer is constructed from pulverized volcanic lava rock
- Inner layer features calcium magnesium silicate wool
- Isolates heat from the compressor side
- Lowers the intake air temperature significantly
- Hand-crafted in the USA!
- One-year warranty
Fitment:
- Polaris RZR XP Turbo 2016-2020
Notes:
- Agency Power Offers a One-Year Warranty Against Defects or Failures
- Product Warranties Are Available For Those Who Fill Out The Online Warranty Form HERE
- Warranty is Available With Original Invoice Showing Purchase Date
Features:
- Fit's Agency Power big turbo upgrade
- Reduces the overall engine bay temperature by 60-percent
- Can withstand 1800°F of direct heat and 2500°F of radiant heat
- The outer layer is constructed from pulverized volcanic lava rock
- Inner layer features calcium magnesium silicate wool
- Isolates heat from the compressor side
- Lowers the intake air temperature significantly
- Hand-crafted in the USA!
- One-year warranty
Features:
- 1065cc/min @ 3.0 Bar (43.5 psi) Using Gasoline at 52 Degrees C (125 Degrees F)
- Maximum Differential Fuel Pressure - 10.0 Bar (145.0 psi)
- Fuel Compatibility - Compatible With All Known Fuels
- Electrical Connector - USCAR
- Corrosion resistant internals make it compatible with all known fuels, capable of extended service life with corrosive fuels.
- Compact body allows fitment in 200+ applications, including current and future engines utilizing short body injectors.
- Improved internal flow path increases output by 5% without sacrificing low flow performance.
- Stronger magnetic circuit offers stable operation up to 10 bar.
- Replaceable inlet filter extends service life.
A Big Brake Kit for the Can-Am Maverick X3 is the modification you never thought about but absolutely need! If you are a Can-Am X3 owner, you already know that the brake pedal is soft and these high horsepower machines do not stop like they should. As a premiere manufacture of UTV products, Agency Power has gone to extreme measures to develop the best 4 wheel big brake kit available for the Can-Am Maverick X3. After extensive testing, we have engineered a brake kit that is a direct bolt-on, provides a proper balanced brake system, and aesthetically looks amazing behind the wheels.
All brake components are manufactured right here in the USA in conjunction with one of the leading performance brake manufactures. This brake system was designed specifically for the Can-Am Maverick X3. With our nearly yearlong testing of different braking concepts and products on the market, we found it absolutely necessary to do a 4 wheel brake kit. With the engine in the rear and how off-road suspension works, typical automotive designs will not produce the improved braking performance the X3 needs. Our calipers are a 2 piece construction that has built in “ears” to mount to the wheel carrier. Removing the need for additional brackets and spacers like other companies may use, gives the Agency Power caliper an extremely rigid advantage. Each caliper half is assembled using 4 10mm cross bolts for maximum stiffness. Other products on the market only use 3/8 inch hardware which is not adequate. This rigidity eliminates caliper flex from hard pedal pressure or the potential of pad knock back. In any motorsport, opposing piston caliper, pad "knock back" can occur from street cars to off-road use. The only way to eliminate this is with a floating caliper design like OEM. However you lose the performance of what a big brake kit can offer.
Internally, the caliper is well designed with custom machined piston sizing that provide an overall surface area comparable to many 6 piston vehicle brakes. Studying the way the vehicle would move under braking allowed us to come up with the proper piston bore for the front and rear calipers. Giving the Can-Am X3 a perfect squat under hard braking allows you to control your vehicle better compared to an unbalanced nose dive. The Agency Power kit has been designed to use the stock master cylinder, stock brake lines, and still provide a much better pedal feel! Another added value of the caliper is the hard anodized aluminum pistons. These are extremely lightweight allowing them to move with ease to help with the clamping force on the rotor. Using both dust and weather seals, the brakes will not have issues from the harsh off-road elements compared to other products that only use pressure seals. With a simple single side bleeder screw, bleeding the brakes does not require you to go from inside to outside on the caliper which saves time. Finally the caliper has an internal cross over to allow brake fluid to go to each side of the caliper and equally put pressure to the pistons. This gives the caliper a clean look and also eliminates the worry about breaking off external cross over pipes found on other systems.
Brake pads for the 4 wheel kit were chosen to provide the optimal performance for the majority of users. With the focus on balance, getting the right friction for the front and rear was important for this setup. The front caliper uses a Hawk HP+ N-Compound while the rear uses a DR1-C ceramic brake pad. Once bed-in properly, the brakes will provide amazing performance without excess squeaking noise. The brake pads are a common shape which allows for ease to access replacement pads. An extremely important part of the big brake kit is the rotors. We utilize a 2 piece cast iron brake rotor just like you would see on high performance car brakes. Cast iron dissipates heat much better than steel like the factory style. Steel will hotspot and throw heat back into the caliper making fluid boil and cause pedal inconsistencies. Cast iron also has a higher coefficient of friction compared to the single thin stamped steel rotor. Each rotor is vented, slotted, and cross drilled. Because the rotors are also directional, while the rotor is spinning, it acts like a pump to cool the brake down. With the rotors larger diameter, this increases torque and leverage of the brake. Since brakes are essentially a heat sink, the better and more accurately we can dissipate heat, the better the brake will perform.
The Agency Power Big Brake Kit is sold as a 4 wheel brake system only. It is designed to be used on 15 inch wheels. We have tested the fitment of the brakes with common wheels such as Method Race Wheels in both a 0mm and 13mm offset as well as Fuel Wheels 38mm offset. The brake kit will not clear the stock 14 inch wheels. It is available in many different color options. Kits include a 1 year manufacture warranty against defects. Replacement and consumable parts are available.
Features:
- Canary Yellow Powdercoated Finish
- CNC Machined Agency Power Logo
- Made in the USA!
- Complete Bolt-On Kit. No Modifications or Additional Parts Required.
- 4 Piston Caliper Specifically Designed for the Can-Am X3
- Dust and Weather Seals for Durability
- Rigid Construction
- Internal Cross Over Tube for Sleek Design
- Common 4 Piston Pad Shape
- No Spacers or Bracket. 1 Piece Mounting
- Banjo Style Fittings. No Cheap Pipe Threads!
- Powdercoated finished with Machined Logo
- 2 Piece Cast Iron Vented Rotor with 6061 T-6 Billet Aluminum Hat
- Cross Drilled and Slotted
- Directionally Designed
- Zinc Coated
- Direct Bolt-On
- Better Heat Dissipation
Specifications:
- Rotor Sizes:
- Stock Front - 260mm
- Agency Power Front – 305mm
- Stock Rear - 250mm
- Agency Power Rear - 305mm
- Caliper Style:
- Stock Front – Sliding 1 Piston
- Agency Power Front – 4 Piston
- Stock Rear – Sliding 1 Piston
- Agency Power Rear – 4 Piston
- Caliper Weight:
- Stock Front - 2.10lbs
- Agency Power Front (no pads) – 3.35lbs
- Stock Rear - 2.40lbs
- Agency Power Rear - (no pads) – 3.35lbs
Kit Includes:
- Front and Rear 4 Piston Calipers
- Front and Rear Directional 2 Piece Rotors Pre-Assembled
- Performance Front and Rear Brake Pads
- Banjo Bolts and Additional Hardware
Notes:
- Brake Installation Guide
- Axle Nut Torque Specs
- Bleeding and Bed-In Process
- Brake Kit Clearance Template
Fitment:
- 2017-2020 Can-Am X3 Turbo, DS, RC, XMR, RS, RR
A Big Brake Kit for the Can-Am Maverick X3 is the modification you never thought about but absolutely need! If you are a Can-Am X3 owner, you already know that the brake pedal is soft and these high horsepower machines do not stop like they should. As a premiere manufacture of UTV products, Agency Power has gone to extreme measures to develop the best 4 wheel big brake kit available for the Can-Am Maverick X3. After extensive testing, we have engineered a brake kit that is a direct bolt-on, provides a proper balanced brake system, and aesthetically looks amazing behind the wheels.
All brake components are manufactured right here in the USA in conjunction with one of the leading performance brake manufactures. This brake system was designed specifically for the Can-Am Maverick X3. With our nearly yearlong testing of different braking concepts and products on the market, we found it absolutely necessary to do a 4 wheel brake kit. With the engine in the rear and how off-road suspension works, typical automotive designs will not produce the improved braking performance the X3 needs. Our calipers are a 2 piece construction that has built in “ears” to mount to the wheel carrier. Removing the need for additional brackets and spacers like other companies may use, gives the Agency Power caliper an extremely rigid advantage. Each caliper half is assembled using 4 10mm cross bolts for maximum stiffness. Other products on the market only use 3/8 inch hardware which is not adequate. This rigidity eliminates caliper flex from hard pedal pressure or the potential of pad knock back. In any motorsport, opposing piston caliper, pad "knock back" can occur from street cars to off-road use. The only way to eliminate this is with a floating caliper design like OEM. However you lose the performance of what a big brake kit can offer.
Internally, the caliper is well designed with custom machined piston sizing that provide an overall surface area comparable to many 6 piston vehicle brakes. Studying the way the vehicle would move under braking allowed us to come up with the proper piston bore for the front and rear calipers. Giving the Can-Am X3 a perfect squat under hard braking allows you to control your vehicle better compared to an unbalanced nose dive. The Agency Power kit has been designed to use the stock master cylinder, stock brake lines, and still provide a much better pedal feel! Another added value of the caliper is the hard anodized aluminum pistons. These are extremely lightweight allowing them to move with ease to help with the clamping force on the rotor. Using both dust and weather seals, the brakes will not have issues from the harsh off-road elements compared to other products that only use pressure seals. With a simple single side bleeder screw, bleeding the brakes does not require you to go from inside to outside on the caliper which saves time. Finally the caliper has an internal cross over to allow brake fluid to go to each side of the caliper and equally put pressure to the pistons. This gives the caliper a clean look and also eliminates the worry about breaking off external cross over pipes found on other systems.
Brake pads for the 4 wheel kit were chosen to provide the optimal performance for the majority of users. With the focus on balance, getting the right friction for the front and rear was important for this setup. The front caliper uses a Hawk HP+ N-Compound while the rear uses a DR1-C ceramic brake pad. Once bed-in properly, the brakes will provide amazing performance without excess squeaking noise. The brake pads are a common shape which allows for ease to access replacement pads. An extremely important part of the big brake kit is the rotors. We utilize a 2 piece cast iron brake rotor just like you would see on high performance car brakes. Cast iron dissipates heat much better than steel like the factory style. Steel will hotspot and throw heat back into the caliper making fluid boil and cause pedal inconsistencies. Cast iron also has a higher coefficient of friction compared to the single thin stamped steel rotor. Each rotor is vented, slotted, and cross drilled. Because the rotors are also directional, while the rotor is spinning, it acts like a pump to cool the brake down. With the rotors larger diameter, this increases torque and leverage of the brake. Since brakes are essentially a heat sink, the better and more accurately we can dissipate heat, the better the brake will perform.
The Agency Power Big Brake Kit is sold as a 4 wheel brake system only. It is designed to be used on 15 inch wheels. We have tested the fitment of the brakes with common wheels such as Method Race Wheels in both a 0mm and 13mm offset as well as Fuel Wheels 38mm offset. The brake kit will not clear the stock 14 inch wheels. It is available in many different color options. Kits include a 1 year manufacture warranty against defects. Replacement and consumable parts are available.
Features:
- Gloss Red Powdercoated Finish
- CNC Machined Agency Power Logo
- Made in the USA!
- Complete Bolt-On Kit. No Modifications or Additional Parts Required.
- 4 Piston Caliper Specifically Designed for the Can-Am X3
- Dust and Weather Seals for Durability
- Rigid Construction
- Internal Cross Over Tube for Sleek Design
- Common 4 Piston Pad Shape
- No Spacers or Bracket. 1 Piece Mounting
- Banjo Style Fittings. No Cheap Pipe Threads!
- Powdercoated finished with Machined Logo
- 2 Piece Cast Iron Vented Rotor with 6061 T-6 Billet Aluminum Hat
- Cross Drilled and Slotted
- Directionally Designed
- Zinc Coated
- Direct Bolt-On
- Better Heat Dissipation
Specifications:
- Rotor Sizes:
- Stock Front - 260mm
- Agency Power Front – 305mm
- Stock Rear - 250mm
- Agency Power Rear - 305mm
- Caliper Style:
- Stock Front – Sliding 1 Piston
- Agency Power Front – 4 Piston
- Stock Rear – Sliding 1 Piston
- Agency Power Rear – 4 Piston
- Caliper Weight:
- Stock Front - 2.10lbs
- Agency Power Front (no pads) – 3.35lbs
- Stock Rear - 2.40lbs
- Agency Power Rear - (no pads) – 3.35lbs
Kit Includes:
- Front and Rear 4 Piston Calipers
- Front and Rear Directional 2 Piece Rotors Pre-Assembled
- Performance Front and Rear Brake Pads
- Banjo Bolts and Additional Hardware
Notes:
- Brake Installation Guide
- Axle Nut Torque Specs
- Bleeding and Bed-In Process
- Brake Kit Clearance Template
Fitment:
- 2017-2020 Can-Am X3 Turbo, DS, RC, XMR, RS, RR
A Big Brake Kit for the Can-Am Maverick X3 is the modification you never thought about but absolutely need! If you are a Can-Am X3 owner, you already know that the brake pedal is soft and these high horsepower machines do not stop like they should. As a premiere manufacture of UTV products, Agency Power has gone to extreme measures to develop the best 4 wheel big brake kit available for the Can-Am Maverick X3. After extensive testing, we have engineered a brake kit that is a direct bolt-on, provides a proper balanced brake system, and aesthetically looks amazing behind the wheels.
All brake components are manufactured right here in the USA in conjunction with one of the leading performance brake manufactures. This brake system was designed specifically for the Can-Am Maverick X3. With our nearly yearlong testing of different braking concepts and products on the market, we found it absolutely necessary to do a 4 wheel brake kit. With the engine in the rear and how off-road suspension works, typical automotive designs will not produce the improved braking performance the X3 needs. Our calipers are a 2 piece construction that has built in “ears” to mount to the wheel carrier. Removing the need for additional brackets and spacers like other companies may use, gives the Agency Power caliper an extremely rigid advantage. Each caliper half is assembled using 4 10mm cross bolts for maximum stiffness. Other products on the market only use 3/8 inch hardware which is not adequate. This rigidity eliminates caliper flex from hard pedal pressure or the potential of pad knock back. In any motorsport, opposing piston caliper, pad "knock back" can occur from street cars to off-road use. The only way to eliminate this is with a floating caliper design like OEM. However you lose the performance of what a big brake kit can offer.
Internally, the caliper is well designed with custom machined piston sizing that provide an overall surface area comparable to many 6 piston vehicle brakes. Studying the way the vehicle would move under braking allowed us to come up with the proper piston bore for the front and rear calipers. Giving the Can-Am X3 a perfect squat under hard braking allows you to control your vehicle better compared to an unbalanced nose dive. The Agency Power kit has been designed to use the stock master cylinder, stock brake lines, and still provide a much better pedal feel! Another added value of the caliper is the hard anodized aluminum pistons. These are extremely lightweight allowing them to move with ease to help with the clamping force on the rotor. Using both dust and weather seals, the brakes will not have issues from the harsh off-road elements compared to other products that only use pressure seals. With a simple single side bleeder screw, bleeding the brakes does not require you to go from inside to outside on the caliper which saves time. Finally the caliper has an internal cross over to allow brake fluid to go to each side of the caliper and equally put pressure to the pistons. This gives the caliper a clean look and also eliminates the worry about breaking off external cross over pipes found on other systems.
Brake pads for the 4 wheel kit were chosen to provide the optimal performance for the majority of users. With the focus on balance, getting the right friction for the front and rear was important for this setup. The front caliper uses a Hawk HP+ N-Compound while the rear uses a DR1-C ceramic brake pad. Once bed-in properly, the brakes will provide amazing performance without excess squeaking noise. The brake pads are a common shape which allows for ease to access replacement pads. An extremely important part of the big brake kit is the rotors. We utilize a 2 piece cast iron brake rotor just like you would see on high performance car brakes. Cast iron dissipates heat much better than steel like the factory style. Steel will hotspot and throw heat back into the caliper making fluid boil and cause pedal inconsistencies. Cast iron also has a higher coefficient of friction compared to the single thin stamped steel rotor. Each rotor is vented, slotted, and cross drilled. Because the rotors are also directional, while the rotor is spinning, it acts like a pump to cool the brake down. With the rotors larger diameter, this increases torque and leverage of the brake. Since brakes are essentially a heat sink, the better and more accurately we can dissipate heat, the better the brake will perform.
The Agency Power Big Brake Kit is sold as a 4 wheel brake system only. It is designed to be used on 15 inch wheels. We have tested the fitment of the brakes with common wheels such as Method Race Wheels in both a 0mm and 13mm offset as well as Fuel Wheels 38mm offset. The brake kit will not clear the stock 14 inch wheels. It is available in many different color options. Kits include a 1 year manufacture warranty against defects. Replacement and consumable parts are available.
Features:
- Hugger Orange Powdercoated Finish
- CNC Machined Agency Power Logo
- Made in the USA!
- Complete Bolt-On Kit. No Modifications or Additional Parts Required.
- 4 Piston Caliper Specifically Designed for the Can-Am X3
-
- Dust and Weather Seals for Durability
- Rigid Construction
- Internal Cross Over Tube for Sleek Design
- Common 4 Piston Pad Shape
- No Spacers or Bracket. 1 Piece Mounting
- Banjo Style Fittings. No Cheap Pipe Threads!
- Powdercoated finished with Machined Logo
- 2 Piece Cast Iron Vented Rotor with 6061 T-6 Billet Aluminum Hat
-
- Cross Drilled and Slotted
- Directionally Designed
- Zinc Coated
- Direct Bolt-On
- Better Heat Dissipation
Specifications:
- Rotor Sizes:
-
- Stock Front - 260mm
- Agency Power Front – 305mm
- Stock Rear - 250mm
- Agency Power Rear - 305mm
- Caliper Style:
-
- Stock Front – Sliding 1 Piston
- Agency Power Front – 4 Piston
- Stock Rear – Sliding 1 Piston
- Agency Power Rear – 4 Piston
- Caliper Weight:
-
- Stock Front - 2.10lbs
- Agency Power Front (no pads) – 3.35lbs
- Stock Rear - 2.40lbs
- Agency Power Rear - (no pads) – 3.35lbs
Kit Includes:
- Front and Rear 4 Piston Calipers
- Front and Rear Directional 2 Piece Rotors Pre-Assembled
- Performance Front and Rear Brake Pads
- Banjo Bolts and Additional Hardware
Notes:
- Brake Installation Guide
- Axle Nut Torque Specs
- Bleeding and Bed-In Process
- Brake Kit Clearance Template
Fitment:
- 2017-2020 Can-Am X3 Turbo, DS, RC, XMR, RS, RR
A Big Brake Kit for the Can-Am Maverick X3 is the modification you never thought about but absolutely need! If you are a Can-Am X3 owner, you already know that the brake pedal is soft and these high horsepower machines do not stop like they should. As a premiere manufacture of UTV products, Agency Power has gone to extreme measures to develop the best 4 wheel big brake kit available for the Can-Am Maverick X3. After extensive testing, we have engineered a brake kit that is a direct bolt-on, provides a proper balanced brake system, and aesthetically looks amazing behind the wheels.
All brake components are manufactured right here in the USA in conjunction with one of the leading performance brake manufactures. This brake system was designed specifically for the Can-Am Maverick X3. With our nearly yearlong testing of different braking concepts and products on the market, we found it absolutely necessary to do a 4 wheel brake kit. With the engine in the rear and how off-road suspension works, typical automotive designs will not produce the improved braking performance the X3 needs. Our calipers are a 2 piece construction that has built in “ears” to mount to the wheel carrier. Removing the need for additional brackets and spacers like other companies may use, gives the Agency Power caliper an extremely rigid advantage. Each caliper half is assembled using 4 10mm cross bolts for maximum stiffness. Other products on the market only use 3/8 inch hardware which is not adequate. This rigidity eliminates caliper flex from hard pedal pressure or the potential of pad knock back. In any motorsport, opposing piston caliper, pad "knock back" can occur from street cars to off-road use. The only way to eliminate this is with a floating caliper design like OEM. However you lose the performance of what a big brake kit can offer.
Internally, the caliper is well designed with custom machined piston sizing that provide an overall surface area comparable to many 6 piston vehicle brakes. Studying the way the vehicle would move under braking allowed us to come up with the proper piston bore for the front and rear calipers. Giving the Can-Am X3 a perfect squat under hard braking allows you to control your vehicle better compared to an unbalanced nose dive. The Agency Power kit has been designed to use the stock master cylinder, stock brake lines, and still provide a much better pedal feel! Another added value of the caliper is the hard anodized aluminum pistons. These are extremely lightweight allowing them to move with ease to help with the clamping force on the rotor. Using both dust and weather seals, the brakes will not have issues from the harsh off-road elements compared to other products that only use pressure seals. With a simple single side bleeder screw, bleeding the brakes does not require you to go from inside to outside on the caliper which saves time. Finally the caliper has an internal cross over to allow brake fluid to go to each side of the caliper and equally put pressure to the pistons. This gives the caliper a clean look and also eliminates the worry about breaking off external cross over pipes found on other systems.
Brake pads for the 4 wheel kit were chosen to provide the optimal performance for the majority of users. With the focus on balance, getting the right friction for the front and rear was important for this setup. The front caliper uses a Hawk HP+ N-Compound while the rear uses a DR1-C ceramic brake pad. Once bed-in properly, the brakes will provide amazing performance without excess squeaking noise. The brake pads are a common shape which allows for ease to access replacement pads. An extremely important part of the big brake kit is the rotors. We utilize a 2 piece cast iron brake rotor just like you would see on high performance car brakes. Cast iron dissipates heat much better than steel like the factory style. Steel will hotspot and throw heat back into the caliper making fluid boil and cause pedal inconsistencies. Cast iron also has a higher coefficient of friction compared to the single thin stamped steel rotor. Each rotor is vented, slotted, and cross drilled. Because the rotors are also directional, while the rotor is spinning, it acts like a pump to cool the brake down. With the rotors larger diameter, this increases torque and leverage of the brake. Since brakes are essentially a heat sink, the better and more accurately we can dissipate heat, the better the brake will perform.
The Agency Power Big Brake Kit is sold as a 4 wheel brake system only. It is designed to be used on 15 inch wheels. We have tested the fitment of the brakes with common wheels such as Method Race Wheels in both a 0mm and 13mm offset as well as Fuel Wheels 38mm offset. The brake kit will not clear the stock 14 inch wheels. It is available in many different color options. Kits include a 1 year manufacture warranty against defects. Replacement and consumable parts are available.
Features:
- Translucent Monster Green Powdercoated Finish
- CNC Machined Agency Power Logo
- Made in the USA!
- Complete Bolt-On Kit. No Modifications or Additional Parts Required.
- 4 Piston Caliper Specifically Designed for the Can-Am X3
- Dust and Weather Seals for Durability
- Rigid Construction
- Internal Cross Over Tube for Sleek Design
- Common 4 Piston Pad Shape
- No Spacers or Bracket. 1 Piece Mounting
- Banjo Style Fittings. No Cheap Pipe Threads!
- Powdercoated finished with Machined Logo
- 2 Piece Cast Iron Vented Rotor with 6061 T-6 Billet Aluminum Hat
- Cross Drilled and Slotted
- Directionally Designed
- Zinc Coated
- Direct Bolt-On
- Better Heat Dissipation
Specifications:
- Rotor Sizes:
- Stock Front - 260mm
- Agency Power Front – 305mm
- Stock Rear - 250mm
- Agency Power Rear - 305mm
- Caliper Style:
- Stock Front – Sliding 1 Piston
- Agency Power Front – 4 Piston
- Stock Rear – Sliding 1 Piston
- Agency Power Rear – 4 Piston
- Caliper Weight:
- Stock Front - 2.10lbs
- Agency Power Front (no pads) – 3.35lbs
- Stock Rear - 2.40lbs
- Agency Power Rear - (no pads) – 3.35lbs
Kit Includes:
- Front and Rear 4 Piston Calipers
- Front and Rear Directional 2 Piece Rotors Pre-Assembled
- Performance Front and Rear Brake Pads
- Banjo Bolts and Additional Hardware
Notes:
- Brake Installation Guide
- Axle Nut Torque Specs
- Bleeding and Bed-In Process
- Brake Kit Clearance Template
Fitment:
- 2017-2020 Can-Am X3 Turbo, DS, RC, XMR, RS, RR
