Side by Side Outlet Parts and Accessories
Unlike other boxes, this design fills the entire bed of the RZR 1000 XP! It is quickly installed or removed using the rubber Lock 'n Ride fasteners that are included. There is a rubber seal on the lid to prevent water, dirt, and other contaminants from penetrating the cargo stored inside. HUGE capacity of 140 Liters. You won't find a better box!
This performance slip-on muffler for the Polaris RZR 800 is designed for maximum airflow without substantially increasing sound level output. it provides a 79% increase in airflow over the stock silencer. This results in a substantial performance improvement, showing better throttle response as well as top-end horsepower. The sound levels are within 2 decibels of stock (90 dBA on the SAE J1287 test) for a trail friendly performance muffler. It also features a removable spark arrestor.
No fuel controller required.
This performance slip-on muffler for the Polaris RZR 570 is designed for maximum airflow without increasing sound level output. It provides a 32% increase in airflow over the stock silencer. This results in a substantial performance improvement, showing better throttle response as well as top-end horsepower. Will not fit 2012 570 RZR, only 13-17 models.
With an exhaust tone that is 3 dB quieter than stock at cruising speeds, this muffler provides a much more relaxing experience when using your Trail, S or XC 900. Idle sound levels are also more subtle with a 2 dB reduction compared to stock! This muffler has superior fit and finish, with fully welded construction for excellent durability. It also comes with black ceramic coating (and an aluminum heat shield) to minimize radiant heat and give it a great look. It will reuse the stock spark arrestor and has also been flow tested and field verified to ensure optimum performance with a quieter exhaust note.
This new cap is very robust in its construction to significantly reduce the binding caused by the stock cap in RZR Turbo and RS1 models. This decreases heat and friction, improves clutching consistency and performance and lengthens clutch and belt life. One key to our design is the tight tolerance bronze bushing that we use. This bushing is flanged to insure that it stays in place and the tighter tolerance between the bushing and the spider nut helps further reduce heat and friction caused by cap bushing bind to eliminate the problem rather than just deal with the headaches the extra heat and friction create. This kit comes complete with a new spider nut that has been machined in the castle area to allow its use with the tight tolerance bushing.
- 3/16” Thick Hard Coated Polycarbonate (both sides).
- Attaches with our Rubber Fast Straps.
- Tool-less removal.
- Rubber edge trim protects and seals along the hood.
- Add an optional hand wiper from the drop down menu.
- Slide vent allows airflow on warm days.
- DOT Rated and stamped with EMP® logo (you should check your local regulations if making it street legal).
- Made and/or assembled In Cleveland Ohio.
Easy Install Black 6″ License Plate Frame with full spectrum 6 white LEDs Hardware Included Made in the USA!
Plug & Play Easy Install Fits 2017-2019 Yamaha Wolverine Includes two .75″ 3 LED front Amber Lights Plugs into OEM Brake Light Harness, using Factory Rear Lights* Laser Etched LED Lit Turn Switch Lit Emergency Hazard Switch*** Rear Power Out for optional license plate light** Made in the USA!
Plug & Play Easy Install Fits 2015-2018 Polaris RZR XP 1000/Turbo Models Fits 2016-Up Polaris RZR 900 with LED Tail lights Includes two .75″ 3 LED front Amber Lights Plugs into OEM Brake Light Harness, using Factory Rear Lights* Laser Etched LED Lit Turn Switch Lit Emergency Hazard Switch Rear Power Out for optional license plate light** Made in the USA!
Plug & Play Easy Install Fits 2019 Polaris Ranger with Factory Installed Ride Command (for non Ride Command, click HERE)
Includes two .75″ 3 LED front Amber Lights Plugs into OEM Brake Light Harness, using Factory Rear Lights* Laser Etched LED Lit Turn Switch Lit Emergency Hazard Switch Rear Power Out for optional license plate light** Made in the USA!
Plug & Play Easy Install Fits 2016-2018 Polaris General 1000 Includes two .75″ 3 LED front Amber Lights Plugs into OEM Brake Light Harness, using Factory Rear Light Laser Etched LED Lit Turn Switch Lit Emergency Hazard Switch Rear Power Out for optional license plate light** Made in the USA!
Fitment:
- 2017-2018 Can-Am Maverick X3, every model
- 2013-2018 Can-Am Maverick, every model
- 2011-2018 Can-Am Commander, every model
- 2008-2018 Can-Am Renegade, every model
- 2006-2018 Can-Am Outlander, every model
- All Years - Can-Am Defender, every model
- 2018 Can-Am Traxter, every model
- ALL Can-Am UTV's and ATV's from 2007 to 2020 (not 2018's with Smart Lok, or 2020+ European Models with Brake Traction Control, "BTC")
